Socket Size Chart In Order

June 16, 2024 Post a Comment

Socket size chart in order

Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)

What are the SAE socket sizes?

The most commonly used and sold SAE sizes for wrenches and sockets are:

5/16″
3/8″
7/16″
1/2″
9/16″
5/8″
11/16″
3/4″

What are the 4 socket drive sizes?

These drive fittings come in four common sizes: 1⁄4 inch, 3⁄8 inch, 1⁄2 inch, and 3⁄4 inch (referred to as "drives", as in " 3⁄8 drive").

What is the next size up from 15 16?

Bolt Diameter	Metric	Standard
1/2"	19mm	3/4"
9/16"	21mm	13/16"
	22mm	7/8"
5/8"	24mm	15/16"

What are the 3 common sizes of ratchets?

Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.

Are 3/4 and 19mm the same?

19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.

What does SAE socket stand for?

SAE sockets: Society of Automotive Engineers (SAE) sockets are manufactured for work on American-made vehicles. Socket sizes are measured based on imperial system inches and fractions. Some of the commonly used SAE sizes are 3/8 in., 5/8 in., and 11/16 in. sockets.

Does SAE mean standard?

SAE, or standard, is used on most domestic models, while metric applies to foreign or non-domestic vehicles. Socket sets and wrench sets are among the most used tools in cases where size measuring differences are important. Notably, SAE tools are measured in fractions of inches, from 5/32 to 2 ½ inches.

What does SAE stand for in measurement?

Standard American English and the Metric System Today, measuring in feet and inches is part of the Standard American English (SAE) or Imperial units of measurement, along with volumes like gallons and fluid ounces and weights like pounds.

What are the 4 different types of sockets?

However, some of the commonest options you would find are 36mm sockets and 10mm sockets. Considering the standard sockets, you can find four common types, and they include 3/4 –inch, ½-inch, 3/8-inch, and ¼-inch sockets. Most of these options mentioned above come with bits that would fit Torx screws.

Do I need a 1/2 ratchet?

1/2 ratchets are great for doing suspension and exhaust work but honestly not needed. You can get by with a 1/2 breaker bar and a good assortment of 3/8 sockets. I rarely use my 1/2 ratchet. I get a lot of use out of mine.

Whats bigger 3/8 or 1/4 socket?

3/8 is expressed as 0.375 as a decimal and 1/4 is expressed as 0.25 in its decimal form. It is clear that the value of 3/8 is more than 1/4. Hence, it is bigger.

Can I use a 3/8 instead of 10mm?

So what is a 10mm socket equivalent? The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.

What size comes after youth 14 16?

The next size up is boys XL 18–20.

What's the next size down from 11 16?

SAE Size	Metric Size	Inches Decimal
21/32″		0.656
	17mm	0.669
11/16″		0.688
	18mm	0.709

What are the 3 types of sockets?

Three types of sockets are supported:

Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
Datagram sockets allow processes to use UDP to communicate. ...
Raw sockets provide access to ICMP.

What are 1/4 ratchets used for?

A 1/4-inch ratchet is best for smaller sockets and precision work. The most versatile ratchet is the 3/8-inch size. This ratchet size can accommodate sockets of all sizes. It is big enough to apply a lot of force, but it can still fit into tight spaces.

What size ratchet is most common?

The most common ratchet sizes are ¼ inch drive, 3/8 inch drive, and ½ inch drive. There are also larger ratchet sizes including ¾ inch drive and 1-inch drive available. Most ratchets used with sockets contain a gear mechanism that is designed to allow for rotation in one direction only.